Page 19 Guide Maximum paper limit To prevent paper jams such as those caused by multiple sheets feeding at once, fan the paper thoroughly, square it, align it with the guide inside, and insert as far as it will go. The lowest level of the board attachment frame is designed for installation of the screen, so the printer cannot be attached at this level. Adjust the level of the screen unit as follows. Height Be sure to tighten the height adjustment handles adjustment handles firmly after adjusting the level of the screen.
Keep the step frame by hanging it on the board attachment upper. Power on the electronic board, and connect the unit and your computer with a USB cable. Power on your computer and start Windows. Note: While the Panaboard Operation Panel is displayed, the Copy Key and 2-Screen Copy Key on the electronic board control panel are used for scanning images into the computer. Stand by: The electronic board is stand by. Both of the Panaboard Operation Panel and the electronic board control panel are operational.
Rotating: The electronic board is rotating the screen. Page Daily Care And Maintenance Daily Care and Maintenance Always turn off the power switch and unplug the power plug when cleaning outside and inside the unit. Page Help Troubleshooting Troubleshooting Treat problems according to the information given in the table below.
If problems still persist, call your dealer for service. Symptom Power switch is on but the indicator is off. Copied copy paper will not come out. Nothing is printed on the paper or copies are faint or blurred. Indication Data transfer error Error The screen will not move. Screen The printer door is not closed securely. This manual is also suitable for: Panaboard ub Print page 1 Print document 36 pages.
Install the new Panasonic-DMS in the same folder with the old one. Error Remove any chart paper attached to The screen will not move.
Page Specifications Specifications Model No. Make sure that all of these parts are included in the package before proceeding. Remove the electronic board from the shipping box. Remove the joints, then remove the electronic board from the shipping box. Page 38 Assembling the Electronic Board Collapse the carton box.
Hang the screen unit to the board attachment upper. Remove the tape and the staples on the unopened side of the carton box, Hold the side covers of the screen unit then collapse the box.
Page 39 Assembling the Electronic Board Extend the screen unit. Extend the screen unit. Open the center and right panels of Hang the right hook of the screen unit the screen unit as shown below and on the board attachment upper. Right hook Cushion Caution Page 41 Assembling the Electronic Board After hanging the screen, fix the Tighten the screws for the printer stopper screw left side only.
This prevents the user from adjusting Use four screws for the optional stand the screen height at the lowest level by and two screws for the wall mounting.
Hook the cover with the projections on both sides, then cover the top of the board attachment upper. Board attachment upper Remove the folding support screw Cover upper on the front side of the screen unit, then store the folding support on Page 43 Assembling the Electronic Board Attach the cover lower.
Attach the rear cover. Fix the cover with the wing bolt. Adhesive tape UB only Rivets Page Electronic Board Operations Check Electronic Board Operations Check After assembling the electronic board, perform the procedures presented in the following table to make sure it functions properly. Normal operation If not Check power cord and cables. Page Repacking Repacking Perform Assembly Steps 2 through 24 in reverse to repack the electronic board and accessories.
Use the joints to fasten the shipping box to the lower box. Slide sheet Extension pipe L is used for UB Step C Insert the screws into the side pipes from the inside. Page Wall-Mounting UB is kgf lbs. The position of the intended installation is of adequate size for the selected Panaboard. Page Wall-Mounting Procedure Confirm that the wall is strong enough to support the weight of the electronic board. Caution The wall must be capable of supporting at least N [ kgf lbs.
Consequently spare parts have been changed to RoHS-compliant parts where applicable. To ensure compliance with the spare parts application of the RoHS legislation, please make sure to follow the details provided in this manual in ordering spare parts and carrying out repairs. Page of 17 Go. Schematics , wiring and block diagrams. Parts list bill of materials.
0コメント